Launch X431 V Plus Pro3 Pro 3 Full System Free Update Multi Car Diagnostic. 2) Click Settings > select Manage Apps. Press on X431 V+ icon and push it up to the trash bin. 1) Click red box marked 1 above. Here lets check how to update the x 431 V / x-431 V+ diagnostic scanner. Launch x431 V / V+ is a typical diagnostic device contributed by Launch to diagnostic industry concerning internet application.
![]() ![]() Launch X431 Download Is CompleteLaunch X431 Password Are CorrectlyIf you forgot the password, tap "Retrieve Password", and then follow the on-screen instructions to retrieve it.How to Set Up Diagun IV Bluetooth Connection?Enter X-431 Diagun IV Bluetooth setting screen ("Settings" -> "Bluetooth"), slide the Bluetooth switch to ON and X-431 Diagun IV will start searching available Bluetooth device, tap the desired connector to pair. Next time you login the system, you will not be asked to input the account manually.3. Once the username and password are correctly entered, the system will automatically store it. If you have registered to be a member, input your name and password, and then tap the "Login" button to enter the main menu screen directly.Note: X-431 Diagun IV has an auto-save function. To resume it, tap "Continue".Once download is complete, the system will install the software package automatically.2. To pause downloading, tap "Pause".On the home screen, tap Settings -> WLAN.2). Once you're online, you can register your X-431 Diagun IV, surf the Internet, get apps, send email, launch the remote diagnosis, and check for software updates etc.1). How to Connect/Disconnect Diagun IV to WiFi?Note: If you don't need to use Wi-Fi for a while, you can turn it off to conserve battery life.X-431 Diagun IV has built-in Wi-Fi that can be used to get online.Launch X431 Update The XWhen this tool is in range, it will connect to the previously linked network automatically.1. Once it is connected successfully, tap the Wi-Fi network from the list to view its name, link speed, security type, IP address etc. When "Connected" appears, it indicates the Wi-Fi connection is complete.Note: When Wi-Fi is not required, this should be disabled to conserve battery power. Select a wireless network, y If the chosen network is open, X-431 Diagun IV will connect automatically y If the selected network is encrypted, a network password will need to be entered.4). Throttle should be in a closed position.If X-431 Diagun IV is testing vehicles equipped with universal OBD II diagnostic socket, please use the included VCI connector. Vehicle battery voltage range should be 9-14 Volts.3. Tap the network with a Connected status, then tap "Disconnect".2. UssearchA vehicle equipped with an OBD II management system supplies both communication and 12V power through a standardized DLC.2. If the DLC cannot be found, refer to the vehicle's service manual.The method used to connect the VCI connector to a vehicle's DLC depends on the vehicle's configuration as follows:1. For some Asian and European vehicles, the DLC is located behind the ashtray and the ashtray must be removed to access the connector. If DLC is not located under dashboard, a label should be there telling location. 4-7 for DLC location of different vehicles. The DLC is usually located 12 inches from the center of the instrument panel, under or around the driver's side for most vehicles. Connect the other end of the adaptor to the included VCI connector.5. Plug the non-16pin end of the connector into the DLC socket, then connect the other end to the OBD I adaptor, and then tighten the captive screws.4. Select the corresponding non-16pin connector.3. Power adaptor: Connect one end of the included power adaptor to DC IN port of X-431 Diagun IV handset, and the other end to AC outlet.For non-OBDII vehicle, proceed as follows:2. Choose one of the two ways to obtain power from:A. Plug the VCI connector into the vehicle's DLC socket (It is suggested to use the OBD II extension cable to connect the VCI connector and DLC socket).3. ![]()
0 Comments
Leave a Reply. |
AuthorEdwin ArchivesCategories |